The Large Pharmaceutical Pro Freeze Dryer is a cutting-edge solution designed specifically for pharmaceutical professionals and research institutions. This compact powerhouse delivers precise and efficient freeze-drying, ensuring the preservation of delicate pharmaceutical products and valuable research samples.
Specialty equipment serves a custom unique purpose. If you are planning on cooking something very specific, you may desire the exact tool for the job. This equipment might include pasta cookers, waffle cone makers, sous vide immersion circulators and more.
I would prefer those fittings to have internal Este rings and knurled thread on ports (similar to R134a vacuum gauge sets) that do not require high torque compression fittings. Finger tight and you are good to go. You spot a leak, change the Este ring and you're back in business.
You cannot run a good commercial kitchen without plenty of food. Commercial walk-in coolers are needed for keeping a lot of food chilled. If you’re running a very large scale operation, then a standard-sized refrigerator will not be enough.
14 Posted December 16, 2015 On 7/31/2015 at 11:12 PM, TonyC said: Here is my first pass on a Vapor Trap... it is an old whole house water filter that I modified. It failed to reduce the moisture in the oil... I'm in the process of modifying it to catch and suspend the moisture in the container long enough for desiccant beads to absorb the water. The air flow comes into the inlet, down the central pipe to the bottom of the screen and filters up through the beads and out the top. I know this was like forever ago, but I thought I would respond anyway. I haven't been on much in a while, I only run my freeze dryer in the winter. So I think you'll find it's a lot harder to remove water vapor from a vacuum than just using desiccant, as the vacuum will just pull the water out of the desiccant.
Posted January 21, 2016 (edited) On 12/1/2015 at 0:16 PM, Jenipher said: Tony, if you see this, I went ahead and purchased the catch can. Do you think it's okay to just purchase a reducer to go from the size of the exhaust to the size of the hose that came with the can? Hopefully I said that in a way that makes sense! As well, does it matter which port is used as "in" and which as "out"? Thanks so much, Jen Hi Jen, Sorry to be gone so long. I did exactly as you proposed. I purchased a brass reducer and pushed the blue hose over it.
The types of cooking equipment you have available are very important for your business, so it’s crucial that you buy the correct equipment website for cooking and preparing mouth-watering meals for guests.
Now that you understand the conditions, you can better understand what happened when we finally turned off our FDer after an extended use in these conditions.
Using sublimation, the food retains much of its original texture, flavor, and nutrition when rehydrated. Freeze drying is broken down into two simple processes: freezing and vacuum drying. Foods are first frozen to well below 0°F. The colder the freeze the more efficient the next step will be. Once frozen, foods are subjected to vacuum drying. The air and water vapor (gas) are removed from the food processing chamber using a vacuum pump. This includes removing the water vapor that was once inside of the foods. When these two steps are properly completed, the food is dry enough to allow for safe storage at room temperature. Is freeze drying food safe?
Some essentials are needed to cook with the main food staples in long term food storage. These mostly are used to make breads from stored grains. The cooking essentials include salt, baking powder, baking soda, and yeast.
I didn’t know you had this feature till one day i got an email and that got me to the sitio were i started looking around. This way I can take a couple months instead of hitting my saving and paying for it at once.
5 Posted September 16, 2015 Thanks dsheidt. I was afraid that the AN8 fittings I could find might not be long enough to provide the space needed so that the oil could flow over the top of the filter, especially given my "disk" method of holding up the can.
Upon turning off the pump (no isolation valve on the pump - standard setup), the chamber pressure rose quite rapidly going to 2000 mTorr and continuing up in a couple of minutes or so.
Utah State University sites use cookies. By continuing to use this sitio you accept our privacy and cookie policy.